Brake caliper bolt torque specs | Infiniti Q50 Forum I'm doing a brake job on my 2014 Infiniti Q50S and would like to know the caliper bolt torque specs for both the front and the rear caliper bolts I haven't taken the calipers off yet but usually there are the slide bolts that are only around 20 ft lbs and the larger bracket bolts that are around 100 ft lbs
Infiniti Q50 2014-present Brake System Bolt Torque Specifications Complete Infiniti Q50 2014-present brake system bolt torque specifications Includes factory torque values for brake caliper bolts, brake carrier bolts, rotor mounting bolts, brake line fittings, brake bleeder screws, and all brake assembly fasteners Essential data for proper brake system assembly and safety-critical maintenance
2015 Nissan Quest - Looking for Brake Service Torque Specs The brakes on my wife's 2015 Quest are starting to squeal (it's the original set with 55K on them), so I'd like to replace the pads for her this weekend rear caliper bolts are also the sliders so 32 ft lbs one of the sliding caliper pins have a wacky bushing that goes on the lower position for both front and rear Infiniti Q50 Q60
SS Brake Line Installation - Infiniti Q50 Install the rear brake line in the following order: Image 1: Install new banjo bolt onto brake line fitting with copper washers as shown in the above front step and utilize a 14mm wrench to attach the new banjo to back of caliper (red arrow), torque between 12 to 14 ft lbs
Torque Specs For Brake Caliper Bracket Bolts - Bryans Garage What Is The Torque Specs For Brake Caliper Bracket Bolts Based on driving behavior and vehicle type, brakes should last around 20,000 to 35,000 miles They still need to change at some points However, you will need mechanical knowledge and the brake torque spec for caliper bracket bolts
Brake Caliber Torque Specs?? - Nissan Armada Infiniti QX56 Forums On the front it's 155 ft lbs on the 2 bolts that hold the torque member to the spindle 32 ft lbs on the 2 bolts that hold the caliper to the torque member On the rear it's 24 ft lbs on the 2 bolts that hold the caliper to the rear corner module
Torque Specs - Infiniti Q50 Forum I was a little stumped at this when I installed sport brakes on my old maxima Maxima FSM calls for 106-126 ft-lbs for the caliper bolts while Infiniti only requires 62 ft-lbs Since the bolts I'm using are the ones the came with the sport caliper, not the oem for maxima, I followed the infiniti (lower) torque spec
Infiniti Vehicle Models Q50 2014-present Torque Specifications Complete Infiniti Vehicle Models Q50 2014-present torque specifications guide Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension Essential information for proper assembly and maintenance
What Are Torque Specs For Brake Caliper Bracket Bolts? - Driving On Road The torque specifications for brake caliper bracket bolts can vary based on the make and model of the vehicle For exact torque values, reference the manufacturer’s literature However, as a general rule, brake caliper bracket bolts are often torqued between 25 and 75 ft-lbs
Torque Specs for OEM Brake Job - Infiniti FX Forum Wheels should be tightened to 83 ft -lb Definitely a wise idea to use a torque wrench for this job, I snapped two of the caliper bolts by using a 1 2" wrench they just kept tightening, and tightening, and tightening Oh, and these specs are from a 2005 service manual The 2006+ may not be the same since they use different calipers
Red Sport Brake Caliper - Infiniti Q50 Forum You may be able to use a torque wrench on the opposite side with 1 bolt to figure out how much force it takes to break loose 1 bolt, and then torque the other side to the same value 2016+ 3 0T RWD, BMS HE, Z1 full catless DPs, Megan Y-pipe