New Cohesion board, K40 laser only fires on test switch, not on panel . . . Machine: K40, Came with a HT XC ON 9 (very similar, if not identical to the HT master) Used HT master install instructions for Cohesion board Board: Laserboard Firmware: Smoothie…that’s what it said on it I don’t know what smoothie is But it works 🙂 Problem Question: I am NOT an expert with wiring etc I’ve tried looking through some similar threads and could not understand
Universal ULS-25 want to Gut and mod - forum. cohesion3d. com I have a K40 that has been working well for me and was going to upgrade it to the cohesion board Then I inherited a working Universal ULS-25 Laser that actually works but has an air cooled 25watt laser and uses an old printer connection This thing is large and very well built compared to my K40 and has a nice big motorized table in it I want to gut the Air Cool and install a 60Watt Water
Amp meter needle moves but theres almost no power from the laser I run LightBurn 1 2 01 and everything works except that when I press “start” on a job the head moves and (interestingly) the Amp meter needle moves, but there’s almost NO POWER (low to no intensity) coming out of the laser no matter what power settings I use in LightBurn
Laser tube dead on arrival? - Community Laser Talk - Cohesion3D Community My orginal K40 worked for 8 months no problems, then the power supply went (input only, probably mosfet or something) Pressing the test button on power supply fired the laser Bought a new supply which worked, but the laser tube was putting out TWO beams, not one, right at the laser tube output Google search told me the tube was faulty After 6 weeks haggling with Vevor who I bought the unit
Can the board be pre wired for plugnplay? Also, I do not plan on installing z table or rotary attachment, but i would like to replace my existing stepper motors to increase engraving speed - can you advise on how many External Stepper Drivers and what type of nema17 motors should I get?
Will the CS3 work with my unit? - Pre-Sales Questions - Cohesion3D . . . I have a Full Spectrum Pro Series 24 with a 90watt tube FS has told me that the control board is out (after a month of troubleshooting) They have advised that i ship the entire unit to them for replacement I would like to fix it without spending $2,500 Will the C3D controller work with this unit? If so, are there other pieces that I will need to add along with the board?
New C3D on K40 install and raster fill speed does not change with . . . K40 M2 Nano C3D Laserboard Firmware:"I have a new board and I’m using whatever it came with I have just installed a new C3D Laserboard on my 4 month old K40 So far, I have gone through the documentation of setting up my bed size and configuration the best I could via the docs guidelines I am not clear as to the exact model of my stock K40 Stepper motors so I am including pictures of that
Z axis turn always in same direction - Board Configuration and Setup . . . Machine: k40 Board: laserboard Firmware: I have a new board but had to put the last firmware in it (smoothie cluster) Problem Question: _installed an external stepper driver for Z axis with the cable provided by c3d when I go in lightburn and press the Z up or Z Down button my motor turn in the same direction… everything is cabled according to the documentation found here in the forum Any
Y axis not homing but able to move - forum. cohesion3d. com Hi, I bought a used k40 with m2 board, replaced board with cohesion3d board, I’m using the firmware as is, no changes Problem Question: so when I try to home the gantry the X axis homes perfectly but the Y only creeps hellip;
Will Cohesion3D LaserBoard work with my laser cutter I am inserted in buying one of you boards and the light burn camera Just wanted to make sure that it will replace the board I have now was going to attach picture but it wont let me Board is LiHUiYU Studio labs on top says m2 nano board model 6c6879-laser-M2:9 the machine is a preenex laser engraver with digital control Please let me know if your board will work so I may place an order